5m-14m Electric Self Propelled Scissor Lift with Extension Platform

Our Mobile Electric Scissor Lift, Single Mast Aerial Work Platform, Small Electric Scissor Lift has widely absorbed the advantages of similar products on the market, so that its main performance has reached the highest industry standards. Our company will strictly abide by our promises, be proactive, further increase investment in research and development, and develop better products to share with users. We will never disappoint you. Our company always implements a rigorous quality control system, with a sound sales network and service system.

A Temporary Elevated Workstation for 14m Projects

XE-A140S is not primarily intended for jobs where the machine is driven continuously from one small service point to another.

Its working method is better suited to projects where the equipment is positioned, supported and then used as an elevated workstation while technicians complete a group of related tasks.

Maximum working height is 14 m and maximum platform height is 12 m.

The 450 kg rated capacity and large working deck make this configuration particularly useful for installation projects that require personnel, tools and suitable components to remain together at height.

2.45 × 1.35m Platform - Space Matters during Installation

At elevated installation height, platform area can be just as important as lifting height.

XE-A140S provides a working platform approximately:

2.45 m long
1.35 m wide

This gives technicians additional room to organize tools, move around the work position and handle suitable installation components.

For long-duration tasks, a larger working deck can reduce the need to repeatedly rearrange equipment or return to ground level.

450kg Capacity for Workstation-Type Tasks

The platform carries up to 450 kg.

This capacity allows the machine to support a working arrangement that may include:

• Installation technicians
• Electrical tools
• Mechanical tools
• Measuring equipment
• Suitable replacement components
• Fasteners and installation accessories

The total platform load must always remain within the rated 450 kg limit.

The value of this capacity is not simply "more weight." It allows the platform to function more effectively as an elevated work area during complex installation tasks.

Position - Support - Work - Relocate

The operating pattern of XE-A140S can be understood in four stages.

Position

Use the auxiliary electric travel function to move the machine to the required work section.

Support

Deploy and adjust the screw-type supports according to the operating procedure.

Work

Raise the platform and complete multiple related tasks from the established work position.

Relocate

After the work section is completed, lower the platform, retract the supports and move the machine to the next area.

This workflow makes XE-A140S particularly suitable for projects divided into clearly defined installation zones.

Best Used for Longer Work Sessions

XE-A140S becomes especially practical when the operator remains elevated long enough to complete several related operations.

Examples include:

Electrical Installation

Technicians can install cable trays, electrical components and related fixtures within the same work section.

Mechanical Installation

The larger platform provides useful room for tools and suitable mechanical components during overhead equipment installation.

Ventilation Work

Duct connections, supports and inspection points can be handled from one established elevated position.

Building-Service Installation

Lighting, fire-protection components and other suspended building systems can be installed section by section.

Industrial Upgrade Projects

Factories undergoing equipment or infrastructure upgrades may use the machine as a supported elevated workstation while one production area is modified.

Why Work Duration Matters

A machine that requires support setup before elevation should be used differently from equipment designed for rapid drive-and-lift cycles.

If a task requires only a few seconds of work at each position, repeated support deployment may not be the most efficient operating method.

XE-A140S is more suitable when:

• Each elevated position involves several tasks
• Operators remain at height for longer periods
• Tools must stay on the platform
• The project is divided into installation sections
• Stable supported setup is preferred before work begins

This makes the machine particularly relevant to planned installation projects rather than short inspection stops.

3kW Lifting System for High-Level Operation

XE-A140S uses a 3 kW lifting motor.

The specified rising time is approximately 90 seconds.

At a 14 m working-height class, project efficiency therefore depends more on good work-zone planning than on repeatedly raising and lowering the platform.

Before elevation, technicians can prepare the required tools and suitable components for the complete work section.

Screw Supports Are Part of the Working Method

XE-A140S uses screw-type support leveling devices.

The supports should be deployed and adjusted before elevated operation in accordance with the operating instructions.

They are not the same system as automatic hydraulic leveling outriggers.

For project planning, customers should allow sufficient surrounding space for support deployment and confirm that the supporting surface is suitable for the machine and support loads.

A Different Choice from Rapid-Mobility Equipment

XE-A140S is most appropriate when the project emphasizes:

• High vertical access
• Large platform area
• 450 kg rated load
• Supported elevated operation
• Longer work time at each position
• Occasional relocation between work sections

If the job instead requires continuous driving between many closely spaced service points, another self-propelled platform configuration may be more suitable.

Project Types That Fit XE-A140S

• Electrical installation in industrial buildings
• Mechanical and pipe-support installation
• Ventilation and duct construction
• Factory renovation projects
• Large warehouse facility upgrades
• Commercial building service installation
• Fire-protection system installation
• Overhead infrastructure work

XE-A140S Workstation Data

• Maximum working height: 14 m
• Maximum platform height: 12 m
• Rated platform capacity: 450 kg
• Platform size: 2.45 × 1.35 m
• Stowed dimensions: 3.03 × 1.60 × 1.90 m
• Power source: DC24V
• Lifting motor: 3 kW
• Driving motor: 0.75 kW
• Machine weight: 2000 kg

FAQ

Q: What type of project is XE-A140S best suited for?

A: It is especially suitable for installation and renovation projects where technicians stay at one elevated work zone long enough to complete several related tasks before the machine is relocated.

Q: Why is the large platform important?

A: The 2.45 × 1.35 m deck gives technicians more room for tools, suitable components and working movement during longer installation tasks.

Q: Is XE-A140S designed for continuous self-propelled movement?

A: Its auxiliary electric travel system is mainly useful for relocating the machine between work sections. The typical workflow is to position the machine, deploy the screw supports, complete the elevated task and then relocate.

Our primary purpose is to give our shoppers a serious and responsible company relationship, giving personalized attention to all of them for 5m-14m Electric Self Propelled Scissor Lift with Extension Platform. Our guideline is to make good use of the complementarities. All of our staffs go forward bravely and make progress, and we will build the brand into a tangible and famous product to create brilliance with the majority of distributors!