How to Lubricate the Moving Parts of a Crawler Scissor Lift
Proper lubrication helps reduce friction, limit component wear, and maintain smooth operation of a crawler scissor lift. However, lubrication points, lubricant specifications, and service intervals vary by model.
Always follow the maintenance manual for the specific machine. Maintenance should only be completed by trained personnel using approved procedures.
Why Lubrication Matters
Moving parts operate under repeated loads during lifting, lowering, travelling, and positioning. Without suitable lubrication, pins, bushings, joints, and contact surfaces may wear more quickly.
Regular lubrication can help:
- Reduce friction and wear
- Support smooth lifting movement
- Protect metal surfaces
- Reduce abnormal noise
- Extend component service life
- Identify maintenance problems earlier
Lubrication does not replace inspection. Damaged, loose, cracked, or excessively worn components must be repaired or replaced.
Common Lubrication Points
Depending on the model, lubrication points may include:
- Scissor-arm pivot pins
- Pin and bushing connections
- Sliding or guide surfaces
- Platform extension rollers
- Entry-gate hinges
- Outrigger pivots, if equipped
- Track-related joints specified in the manual
- Other manufacturer-identified grease points
Do not apply grease to electrical components, braking surfaces, hydraulic-cylinder rods, tracks, or other areas unless the maintenance manual specifically requires it.
Safety Precautions
Before beginning maintenance:
- Park the machine on a firm, level surface
- Lower the platform completely where possible
- Switch off the machine
- Remove the key or isolate the power supply
- Secure the equipment against movement
- Keep other personnel away
- Wear suitable personal protective equipment
Never work beneath a raised platform or scissor structure unless it has been secured with the manufacturer-approved maintenance support.
Do not rely only on the hydraulic system to hold an elevated structure.
Clean the Lubrication Points
Clean each grease fitting and surrounding area before applying lubricant.
Crawler lifts may operate in mud, dust, sand, or other contaminated environments. Applying grease over dirt can push abrasive material into pins and bushings.
Use a clean cloth or suitable cleaning method to remove:
- Dirt
- Mud
- Old grease
- Dust
- Moisture
- Other contaminants
Check that the fitting is not damaged or blocked.
Use the Correct Lubricant
Use only the lubricant specified in the applicable maintenance manual.
The correct lubricant depends on:
- Component design
- Operating temperature
- Environmental conditions
- Load requirements
- Manufacturer specifications
Do not mix different grease types unless compatibility has been confirmed. Incompatible lubricants may separate, harden, or lose their protective properties.
Apply the Correct Amount
Connect the grease gun securely to the fitting and apply lubricant gradually.
Stop when:
- The specified amount has been applied
- Fresh grease appears at the approved outlet point
- The maintenance procedure indicates completion
Avoid excessive lubrication. Too much grease may attract dirt, damage seals, or hide component problems.
Remove excess grease after servicing to keep the area clean.
Inspect Components During Lubrication
Lubrication provides a useful opportunity to inspect the machine.
Look for:
- Loose or missing fasteners
- Damaged pins
- Worn bushings
- Cracks or deformation
- Corrosion
- Uneven movement
- Abnormal clearance
- Hydraulic leaks
- Damaged grease fittings
- Unusual noise
If excessive wear or structural damage is found, remove the machine from service and arrange inspection by qualified personnel.
Lubrication Frequency
Lubrication intervals should follow the maintenance schedule for the specific model.
More frequent inspection may be required when the machine operates in:
- Dusty environments
- Muddy ground
- Wet conditions
- Corrosive areas
- High or low temperatures
- Intensive daily operation
Do not assume that every lubrication point requires daily greasing. Over-lubrication can also cause problems.
After Lubrication
After completing the work:
- Wipe away excess grease
- Confirm that all fittings are protected
- Remove tools and cleaning materials
- Remove maintenance supports according to the approved procedure
- Restore the machine to normal condition
- Complete the required function test
- Record the maintenance activity
Operate the lift slowly during the initial test and check for smooth movement, abnormal noise, warning indicators, or leaks.
Common Lubrication Mistakes
Avoid the following practices:
- Using an unspecified lubricant
- Applying grease without cleaning the fitting
- Mixing incompatible products
- Adding excessive grease
- Lubricating while the machine is operating
- Working beneath an unsupported platform
- Ignoring damaged pins or bushings
- Using lubrication to hide noise or wear
- Failing to record completed maintenance
Frequently Asked Questions
Can any general-purpose grease be used?
No. Use the lubricant specified for the exact model and component.
Should crawler tracks be covered with grease?
Not unless the maintenance manual specifically requires it. Grease may attract dirt and affect some track components.
How often should the lift be lubricated?
Follow the model-specific maintenance schedule. Operating conditions may require more frequent inspection.
Can lubrication repair worn components?
No. Lubrication may reduce friction, but it cannot repair damaged pins, bushings, bearings, or structural parts.
Conclusion
Correct lubrication supports the smooth operation and service life of a crawler scissor lift.
Maintenance personnel should:
- Follow the applicable manual
- Secure the machine before servicing
- Clean lubrication points
- Use the specified lubricant
- Apply the correct amount
- Inspect components for wear
- Record the completed maintenance
Contact Mantall for model-specific maintenance information, technical documentation, spare parts, and crawler scissor lift support.

